Free tools / Scuba calculators
Free scuba calculator
Scuba weight calculator
Free scuba weight calculator and dive weight calculator. A starting estimate in pounds or kilograms from body weight, exposure suit, salt or fresh water, and tank type.
For planning and education only. Not a substitute for training, certification limits, or a dive computer.
Starting weight estimate
Do a weight check at the surface before you rely on this. With an empty BCD and a normal breath, float at eye level, then sink slowly as you exhale. Take only enough lead to do that in the water you will dive.
Units
Water
Starting point, not the final lead
8.0 kg
- Suit band
- 4.0 kg
- Salt-water density allowance
- 2 kg
- Aluminum 80, empty
- 2 kg
Change the lead until the surface check passes. A new suit, a different tank, and salt versus fresh water all move the number.
What this estimate is, and what it is not
This is a starting pile of lead so the weight check is not a wild guess. It is not the amount you should dive. DAN's "Weight Up!" article says to start from body weight, the exposure suit, the equipment, and the water, and then it says the percentages are only starting points. Body composition changes the result. So does a new suit that has not been compressed yet.
Do the check at the surface, in the water you will dive, in the gear you will wear. Scuba Diving magazine describes the check taught in PADI Peak Performance Buoyancy: empty BCD, normal breath, float at eye level, sink slowly when you exhale. If you are light, add a small amount and check again. If you are stuck under the surface with a normal breath, take lead off. The Open Water guide is where that skill is supposed to be learned with an instructor, not from a web page.
Check with a low cylinder when you can. An aluminum tank gets more buoyant as you breathe it down, and a check on a full tank can feel fine at the start and light on the safety stop. Scuba Diving says that if you must check on a full tank, add about 5 lb for a typical cylinder's buoyancy gain by the time you reach reserve. The aluminum line in this calculator is a different figure: the empty buoyancy, so the estimate is aimed at the end of the dive rather than the start.
The rules of thumb, and where each number comes from
DAN: about 10% of body weight as a baseline for a 6 mm full wetsuit, and about 5% for a 3 mm suit. Aluminum needs more lead than steel. Salt water needs more lead than fresh water, and DAN says the difference varies by person. They do not publish a single salt-water bonus.
Scuba Diving, citing the starting suggestions from PADI Peak Performance Buoyancy: a dive skin or swimsuit at 0.5 to 2 kg (1 to 4 lb); 3 mm at 5% of body weight; 5 mm at 10%; 7 mm with hood and gloves at 10% plus 1.5 to 3 kg (3 to 5 lb); a neoprene drysuit at 10% plus 3 to 5 kg (7 to 10 lb). The metric and imperial add-ons in that article are rounded differently, so this calculator applies the kilogram add-on when you are in kilograms and the pound add-on when you are in pounds.
Salt water then adds 2.5% of body weight. NOAA's World Ocean Database uses 1025 kg/m3 as a constant seawater density when it converts units. Fresh water is about 1000 kg/m3. The 2.5% line is that density gap applied to body weight. It is a physics estimate, not a number from DAN or PADI. If your pool check already felt right, do the ocean check anyway. Do not stack this 2.5% on top of a check you already did in salt water.
An aluminum 80 adds 4.4 lb (about 2.0 kg). Huron Scuba's cylinder table, which says it was compiled from Luxfer and Catalina specifications, lists a Luxfer 80 at +4.4 lb empty with the valve, in seawater, and a Catalina S80 at +4.0 lb. Steel cylinders on that table are often neutral or negative when empty, so steel adds 0 here. Your own cylinder can differ. "Tank not included" also adds 0.
Worked example, fresh water, no tank allowance: 80 kg in a 3 mm suit is 5% = 4 kg. The same diver in salt water with an aluminum 80 is the 4 kg suit band, plus 2 kg of density allowance, plus about 2.0 kg of empty-tank buoyancy, about 8.0 kg before the weight check. A 180 lb diver in a 7 mm suit, fresh water, no tank allowance, lands on 21 to 23 lb: 10% is 18 lb, plus the 3 to 5 lb the Peak Performance list adds for hood and gloves.
Common mistakes
Diving the number on this page without getting in the water. The check is the result. The calculator is the guess you carry to the check.
Copying a buddy's belt. Body size, suit, and cylinder are doing different jobs.
Using pool lead in the ocean, or last year's tropical 3 mm lead in a 7 mm. Change one variable and check again.
Adding "a bit extra so I can get down." Extra lead feels stable until you are overweighted, breathing hard, and fighting the BCD. Take the minimum that passes the eye-level check.
Forgetting that gas time and weighting interact on an aluminum tank. A light stop at reserve pressure is a weighting problem and an air problem. The SAC rate calculator is the air half. Neither one replaces the weight check or a dive computer.
Sources
Questions
- Is this the amount of lead I should dive with?
- No. It is a starting point for the weight you take to the water. DAN and the PADI Peak Performance Buoyancy starting points published by Scuba Diving magazine both say the percentages are only a start. Do a surface weight check in the gear and the water you will actually dive.
- How do I do a proper weight check?
- At the surface, with an empty BCD and a normal breath, you should float at eye level and sink slowly when you exhale. Scuba Diving magazine describes that check as the one taught in PADI Peak Performance Buoyancy. Do it in salt water if the dive is in salt water, and in fresh water if the dive is in fresh water.
- Why does salt water change the estimate?
- Salt water is denser, so the same diver needs more lead than in fresh water. DAN says the extra amount varies by person and does not publish one number. This calculator adds 2.5% of body weight in salt water because NOAA's World Ocean Database uses 1025 kg/m3 as a constant seawater density, against fresh water near 1000 kg/m3. That line is a density estimate, not an agency table.
- Why does an aluminum tank add lead when a steel tank does not?
- A common aluminum 80 is positively buoyant when it is low on gas. A specification table compiled from Luxfer lists the aluminum 80 at +4.4 lb empty with the valve, in seawater. Many steel cylinders are neutral or negative when empty, so this calculator adds no lead for steel. Your cylinder's own buoyancy can differ.
- I was fine on the first dive and light on the safety stop. What happened?
- An aluminum cylinder gets more buoyant as pressure drops. A check on a full tank can hide a light stop at the end. The aluminum figure here is the empty-tank buoyancy, so the estimate is aimed at the end of the dive. Confirm it with a low tank, or near your reserve, before you trust it.
Other scuba calculators
- Scuba calculators. Nitrox MOD, equivalent air depth, best mix, SAC rate, and a starting weight estimate. Free, in the browser.
- Nitrox MOD calculator. Maximum operating depth from the oxygen percent and a maximum PO2. Defaults to 1.4, with the 1.6 contingency.
- EAD calculator. Equivalent air depth for a nitrox mix at a planned depth, in meters or feet.
- Nitrox best mix calculator. The richest whole-percent oxygen mix for a planned depth and PO2, rounded down, capped at recreational limits.
- SAC rate calculator. Surface air consumption and RMV from pressure used, tank size, depth, and time, plus how long a tank lasts.