Free tools / Scuba calculators

Free scuba calculator

SAC rate calculator

Free SAC rate calculator for scuba. Surface air consumption and RMV from pressure used, tank size, depth, and time. Metric or imperial, bar or psi, plus how long a tank lasts.

For planning and education only. Not a substitute for training, certification limits, or a dive computer.

SAC, RMV, and tank time

Mode

Units

Water

Start pressure minus end pressure for the timed segment.

Use a steady depth, the way DAN describes the timed swim.

A 12 L cylinder is a common metric rental tank. Ideal gas: free liters = bar x liters.

SAC and RMV

2 bar/min

RMV 24 L/min

Absolute pressure 2 ATA. Surface volume used 480 L. Ideal gas, with no compressibility correction.

What SAC and RMV mean

Divers Alert Network, in Mike Ange's Alert Diver article, defines surface air consumption as a pressure rate: psi per minute or bar per minute, brought back to the surface. That number belongs to the cylinder you measured it on. A bigger cylinder loses pressure more slowly for the same breaths.

RMV on this page is the volume version of that same surface rate, in liters per minute or cubic feet per minute. It is the figure you can carry to a different cylinder. Naming is messy in print. TDI/SDI's air-management article uses "SAC" for a surface volume around 14 to 16 liters a minute, and "RMV" for the at-depth volume after you multiply by pressure. Here, SAC is DAN's pressure rate and RMV is the surface volume. The at-depth burn is just that rate times atmospheres. The label on the result says which one you are looking at.

The reverse mode answers a narrower question: how many minutes the gas above your reserve lasts at one depth. It rounds down. It is not a dive plan. It does not include the descent, a sawtooth profile, a safety stop, or a decompression schedule. Open Water students meet the idea of watching the gauge in the PADI Open Water guide. This page turns that habit into a number.

Formula and a worked example

Seawater absolute pressure is depth / 10 + 1 atmospheres in meters, or depth / 33 + 1 in feet. Fresh water uses 10.3 m or 34 ft. DAN's worked example is a 10 minute swim at 33 ft (10 m), using 600 psi, which they also write as 40 bar to keep the metric arithmetic round. They note that 600 psi is actually about 41.38 bar.

SAC = (pressure used / minutes) / ATA

RMV = SAC x cylinder volume per pressure unit

Minutes at depth = usable pressure / (SAC x ATA), rounded down

Imperial, on a cylinder rated 77.4 cu ft at 3,000 psi: 600 / 10 = 60 psi per minute at depth. ATA is 2. SAC is 30 psi/min. RMV is 30 x (77.4 / 3000) = 0.774 cu ft/min.

Metric, DAN's rounded 40 bar on a 12 L cylinder: 40 / 10 / 2 = 2 bar/min. RMV is 2 bar/min x 12 L = 24 L/min. Free gas is pressure times water capacity. That is the ideal-gas shortcut. It ignores compressibility, which matters more at high fill pressures than this planning sketch does.

Tank time, using that 30 psi/min SAC, a 3,000 psi fill, a 500 psi reserve, at 99 ft (4 ATA): usable gas is 2,500 psi, depth consumption is 120 psi/min, and 2500 / 120 = 20.8 minutes. Rounded down, plan on 20 minutes at 99 ft, then you are at the reserve. You still need gas for the trip up.

Typical values, only where a source gives them

TDI/SDI says an average baseline for a relatively experienced diver is around 14 to 16 liters a minute, about 0.5 to 0.6 cubic feet a minute, and that many textbooks use a figure in that range. DAN's air guide publishes surface ventilation by workload, not by experience: about 8 L/min at rest, 20 L/min at light to moderate activity, and 70 L/min during vigorous exercise. At 30 ft they list those rates doubled, and at 100 ft they list them at four atmospheres.

I am not adding a separate band for new divers. I do not have a sourced one. Cold, current, a new suit, and task loading move a measured rate more than a label does. Measure a steady 10 minute segment the way Ange describes, on the cylinder you actually dive, and write that RMV in the log.

Common mistakes

Comparing a psi-per-minute SAC with someone on a different cylinder. Convert to RMV first.

Using one average depth for a dive that spiked much deeper. The estimate assumes the depth you type was the depth for the whole timed segment.

Forgetting the reserve, or treating the minute count as the whole dive including the ascent.

Copying a textbook 15 L/min instead of measuring. The textbook figure is a planning example. Yours might be quieter or much higher.

Turning this into a decompression plan. It will not. Gas time and oxygen limits are separate: the MOD calculator does not know how fast you breathe, and this page does not know your no-decompression limit.

Sources

Questions

What is the difference between SAC and RMV?
On this page, SAC is the surface gas rate in bar per minute or psi per minute for the cylinder you measured. RMV is the same rate as a volume: liters per minute or cubic feet per minute. RMV travels with you to another cylinder. A psi-per-minute SAC does not, unless the cylinder is the same size and rated pressure.
Why is my psi-per-minute SAC different from my buddy's?
Pressure drop depends on the cylinder. A larger cylinder loses fewer psi for the same breaths. Compare RMV, or compare SAC only when you both dove the same cylinder size and rated pressure.
How does the tank-duration estimate work?
It divides the gas above your reserve by the consumption at the depth you enter, then rounds the minutes down. The result is time at that depth, not a full dive with a descent, a multilevel profile, or an ascent.
What is a typical SAC or RMV?
TDI/SDI's air-management article says a relatively experienced diver is often around 14 to 16 liters a minute, about 0.5 to 0.6 cubic feet a minute, and that textbooks use a figure in that range. DAN publishes surface ventilation of about 8 L/min at rest, 20 L/min at light to moderate activity, and 70 L/min at vigorous exercise. Those are workload figures, not a new-diver versus experienced-diver standard. Measure your own.
Does this include a safety stop or decompression?
No. It does not build a dive profile, a no-decompression limit, or a decompression schedule. Keep the reserve your team agreed, and plan the ascent with your training and your computer.
  • Scuba calculators. Nitrox MOD, equivalent air depth, best mix, SAC rate, and a starting weight estimate. Free, in the browser.
  • Nitrox MOD calculator. Maximum operating depth from the oxygen percent and a maximum PO2. Defaults to 1.4, with the 1.6 contingency.
  • EAD calculator. Equivalent air depth for a nitrox mix at a planned depth, in meters or feet.
  • Nitrox best mix calculator. The richest whole-percent oxygen mix for a planned depth and PO2, rounded down, capped at recreational limits.
  • Scuba weight calculator. A starting weight estimate from body weight, exposure suit, salt or fresh water, and tank type. Check it in the water.